Using optical maps

Warning

Work in progress, more will be added later!

Creating optical maps

1. Running remage simulations to get an stp file

The map generation is performed directly with remage (reboost is not involved in this step). An example macro to showcase the required settings (map.mac):

/RMG/Processes/OpticalPhysics true
/RMG/Processes/OpticalPhysicsMaxOneWLSPhoton true

/RMG/Geometry/RegisterDetectorsFromGDML Optical

/RMG/Geometry/GDMLDisableOverlapCheck true

/run/initialize

/RMG/Output/NtuplePerDetector false
/RMG/Output/Vertex/StorePrimaryParticleInformation false
/RMG/Output/Vertex/StoreSinglePrecisionEnergy true
/RMG/Output/Vertex/StoreSinglePrecisionPosition true

# confinement in disk around array
/RMG/Generator/Confine Volume

/RMG/Generator/Confinement/SamplingMode IntersectPhysicalWithGeometrical
/RMG/Generator/Confinement/ForceContainmentCheck true

/RMG/Generator/Confinement/Physical/AddVolume lar

/RMG/Generator/Confinement/Geometrical/AddSolid Cylinder
/RMG/Generator/Confinement/Geometrical/CenterPositionX 0 m
/RMG/Generator/Confinement/Geometrical/CenterPositionY 0 m
/RMG/Generator/Confinement/Geometrical/CenterPositionZ 0.69 m
/RMG/Generator/Confinement/Geometrical/Cylinder/InnerRadius 0 m
/RMG/Generator/Confinement/Geometrical/Cylinder/OuterRadius 0.7 m
/RMG/Generator/Confinement/Geometrical/Cylinder/Height 2.4 m

/RMG/Generator/Select GPS
/gps/particle     opticalphoton
/gps/ene/type     Gauss
/gps/ene/mono     9.68 eV # 128nm (VUV) LAr scintillation
/gps/ene/sigma    0.22 eV # gaussian width
/gps/ang/type     iso
# use random polarization (this emits warnings that can be ignored)
#/gps/polarization 1 1 1

/run/beamOn 80000000

Run remage with this macro to produce the (flat) output file:

$ remage -g l200-geometry.gdml -o map.stp.lh5 --flat-output -- map.mac

2. Create the map

with a map settings file (map-settings.yaml):

range_in_m:
  - [-0.7, 0.7]
  - [-0.7, 0.7]
  - [-0.51, 1.89]
bins: [280, 280, 480]

$ reboost-optical createmap --settings map-settings.yaml --geom l200-geometry.gdml map.stp.lh5 map.map.lh5

createmap can also work on multiple input files at once. Make sure that enough memory is available; the map object is fully stored in memory. In this example: For the 58 hardware channels, the example above would require

\[\text{memory} = 8 \cdot n_x \cdot n_y \cdot n_z \cdot (n_\text{ch} + 4) = 8 \cdot 280 \cdot 280 \cdot 480 \cdot (58 + 4) = 19 \times 10^{9} \, \text{bytes}\]

but peak memory usage might be higher. The input buffer will also use some memory.

For parallelization, createmap supports a -N <n_cpu> argument. However, this cannot be scaled indefinitely. Be aware of the memory configuration of the compute node used (i.e., performance may suffer when using more processors than in a NUMA domain). createmap internally uses locks to access one shared memory instance of the to-be-created map. The more CPUs are used for the task, the more lock contention might happen.

Note

In practice, a specific scheme has been shown to be working for large LEGEND maps. 16 cores on a NERSC perlmutter node work quite fine to produce a map from a set of input files. To use more of the available resources, 256 input files are used for one createmap task; up to 16 (typically only 12 to have some spare memory for the peaks) such tasks are run in parallel. This means a total of 4096 remage output files can be read in parallel.

The 12-16 output files can then be combined into one with

$ reboost-optical mergemap --settings map-settings.yaml map.map*.lh5 final-output-map.lh5

Applying optical maps to physics simulations

Integration into build-hit

reboost-optical is integrated with the remaining reboost stack. The map-based production of the optical response is divided into multiple steps:

  1. generation of primary emitted photon counts (the same for all detecting channels)

    \[n_\mathrm{emitted}(E_j) \sim \mathcal{P}(Y\, E_j)\]

    This is implemented in the processor reboost.spms.pe.emitted_scintillation_photons().

  2. sampling of the actually detected photons (individually per channel)

    \[ n_c(E_j) \sim \mathcal{P}\left( n_\mathrm{emitted}(E_j) \, \cdot\, \ \xi_c(x_j)\, \epsilon_c \right)\]

    where \(\xi_c\) is the loaded optical map, and \(\epsilon_c\) is an arbitrary user-supplied scaling factor for the channel \(c\).

    This is implemented in the processor reboost.spms.pe.detected_photoelectrons().

The used statistical model are developed and described in more detail in M. Huber’s master thesis.

An example using all these processors can be seen in the documentation of reboost.build_hit. Especially note the usage of pre_operations and detector_mapping to convert a single input table of type scintillator to multiple optical output tables.

Standalone tool reboost-optical convolve (deprecated)

Important

This old standalone method is deprecated and will be removed in a future version of reboost.

If the liquid argon volume is registered as a Scintillator detector with uid 1, the optical response can be created with:

reboost-optical convolve --material lar --map map.lh5 --edep remage-output.lh5 --edep-lgdo /stp/det001 --output optical-response.lh5